A motorcycle's idle speed determines how fast it moves forward when the brake is released with the engine running. On bikes with carburetors, the idle speed is adjusted using the idle screw. For fuel-injected bikes, the idle speed can often be adjusted with a knob located in the engine compartment.
Steps to Follow
Finding and Using the Idle Screw

Consult your motorcycle's manual to locate the recommended idle RPM. The manual will specify the ideal idle speed, typically between 700-1,000 RPM. If your bike has a tachometer, you can use it to check the RPM while the bike is running. Otherwise, listen for a low buzzing sound at idle, indicating the correct RPM.

Locate the carburetor on your motorcycle by checking next to the engine. Consult your manual's diagram to find its exact position. The carburetor, a large metal component with a pipe on top and a circular port on the side, is usually situated near or beneath the engine.

Find the idle screw near the base of the float bowl, identified by a spring. The float bowl, akin to a miniature gas tank at the carburetor's bottom, houses this screw. Look for a screw connected to a 1–2 in (2.5–5.1 cm) coil. The coil may be positioned vertically or horizontally against the carburetor.
Tip: The idle screw typically features a Phillips head. Avoid adjusting the nearby flathead screw, which controls air intake during active riding. Messing with this screw can affect air flow, so it's best left alone.

Remove any obstructing trim to access the screw if needed. Use an Allen or socket wrench to remove bolts or screws securing the trim. Then, carefully lift off the panel. Some panels have clips that can be gently pried open to remove them.
Adjusting the Idle Screw

Start your motorcycle and allow 2-3 minutes for the engine to stabilize. Engage the kickstand and turn on the motorcycle. Wait for about 2 minutes to ensure the engine reaches a consistent temperature and speed. It's preferable to adjust the idle screw while the engine is running, as it allows the engine to adapt gradually to the changes with fuel flowing through it.

Monitor your idle RPM using the tachometer if available. If your motorcycle is equipped with an RPM gauge (tachometer), observe the gauge while the bike is idling. If the RPM falls within the acceptable range, there's no need to adjust the idle settings with the screw. Otherwise, determine whether you need to raise or lower the idle speed.
Tip: Without a tachometer, rely on engine sound and bike feel while riding. Typically, idle should produce a low rumble, and the bike should move at a moderate speed for stabilization without requiring a foot on the ground when released.

Turn the screw clockwise to raise the idle speed. If the idle speed is too low, use a Phillips head screwdriver to turn the idle screw clockwise. For vertical coil configurations with the screw at the bottom, turn counterclockwise when viewed from above. Make minor adjustments by turning the screw 1-2 times, or 3-5 times for significant increases in idle RPM.

Rotate the screw counterclockwise to lower the idle speed. Decrease the idle speed by turning the screw counterclockwise. Adjust the screw 1-5 times depending on the desired reduction in idle speed.

Check the tachometer gauge after adjusting the screw if available. Immediately observe the tachometer's needle after making adjustments to the idle screw. Verify if the RPM falls within the manufacturer's recommended range. Continue making tweaks until the needle indicates an acceptable idle speed.

Test the bike by releasing the brake to assess its feel. Once you've made adjustments to the idle screw, sit on your bike and raise the kickstand with your foot. Release the brake to allow the bike to idle for a short distance. Assess whether the idle speed feels appropriate. If not, make further adjustments as necessary to achieve the desired speed.
Helpful Tips
-
On fuel-injected motorcycles, don't be alarmed if the idle speed initially seems high upon startup. These bikes often have a naturally high idle speed at first to warm up the engine quickly, which is normal.
-
Issues with idle speed on fuel-injected motorcycles may indicate underlying mechanical problems or a dirty throttle. Thoroughly clean the bike to check if a dirty throttle body is causing the issue. If problems persist, consult a professional mechanic to inspect for vacuum leaks, speed sensor issues, or motor problems.
-
This process also applies to dirt bikes and ATVs, although the RPM requirements for these vehicles may vary.
Essential Items
- Phillips head screwdriver
- Allen wrench (optional)
- Socket wrench (optional)