Reviving Dry Correction Ink: A Step-by-Step Guide

Correction fluid is used to cover mistakes made with ink on paper. If left unused or not properly sealed, the fluid can dry out. However, you can extend the lifespan of your correction fluid by rehydrating it.

1. Add a Drop of Water: Pour a small amount of water or correction fluid thinner into the dried-up bottle. Replace the cap and shake well to mix the contents thoroughly.

Revive Your Correction Ink with Non-Acetone Nail Polish Remover: Open the correction ink bottle and carefully add three drops of non-acetone nail polish remover using an eyedropper. Close the bottle tightly and shake it well to ensure thorough mixing. Test the ink consistency, and if it's still too thick, add two more drops of nail polish remover.

Use White-Out Thinner to Restore Your Correction Ink: Purchase white-out thinner from an office supply store. Add three drops of the thinner to the correction ink bottle using an eyedropper. Close the bottle tightly and shake it vigorously to combine the ingredients. Test the ink on a piece of paper, and if it remains too thick, add two more drops of the thinner. Remember to shake the bottle before testing the ink again. This product may also be labeled as 'correction ink thinner' or 'correction fluid thinner.'

Inspect the Nib: Before attempting any restoration method, examine the nib of the correction ink pen. Sometimes, a thin layer of dried ink covers the nib, while the ink inside the pen remains usable.

Remove Dried Ink from the Nib:

If the nib is covered with dried ink, gently scratch it off using your fingernail. This thin layer of dried ink may obstruct the flow of fresh ink from the pen.

Give the pen a vigorous shake and test it. This action helps dislodge any blockages inside the ink. After shaking the pen, try drawing with it to see if the ink flows smoothly.

Dismantle the pen if the blockage is within the tube. You may need to detach the top and bottom sections of the pen, depending on its design. Use a long, slender object like a knitting needle or chopstick to remove the clot.

Try diluting the ink. Use a few drops of water or non-acetone nail polish remover to thin out the ink inside the pen.

Refill the pen with fresh ink if necessary. If the ink has dried out beyond restoration, pour some fresh correction ink into the pen capsule from a white correction ink bottle.

Reassemble the pen and shake it well. If any parts don't stay together, you can use super glue to seal them if needed.

Know what to do if the ballpoint gets stuck. Sometimes, a correction ink pen may fail to write because the tiny ball in the tip is stuck. You can loosen it using either of these methods:

• Draw circles with it in a small pool of olive oil or baby oil.
• Soak the tip in a cup of warm water for approximately 10 minutes.

Always keep the bottle lid tightly closed when not in use. Exposure to air can cause the ink to harden and dry. The longer the bottle remains open, the thicker the ink will become.

Ensure correction pens are capped when not in use. Even though the ink is housed inside the pen capsule, keeping the cap on is essential. This not only prevents leakage but also slows down ink drying on the nib. If ink dries on the nib, it may lead to blockages.

Consider cleaning the inner neck of the bottle with nail polish remover. Periodically, you may want to open your correction fluid bottle and wipe the neck area, particularly where the threads are located. Dampen a folded paper towel with nail polish remover and wipe it around the bottle's neck. This removes any excess ink that may have dried on the bottle's neck, ensuring a tight cap seal and preventing air from entering.

Regularly clean the nib of your correction ink pen. Periodically, swipe the pen across some paper to prevent ink buildup. Additionally, remove any dried ink from the ballpoint using your fingernail to avoid blockages.

Store correction ink pens upright in a jar. Ensure the tip is facing upward when storing. Storing the pen on its side or upside down may cause the ink to flow into the nib and dry out.

Keep correction fluid in a cool, dry place. Avoid exposing it to sunlight and heat, as both can lead to ink drying and hardening.