Buzz
If you're throwing a party or preparing for a festive occasion, adding some bunting to your decor can liven things up. Whether you have a patriotic flag or a string of decorative triangles, all you need are a few basic tools to hang your bunting indoors or outdoors. In just a few minutes, your space will be holiday-ready.
Instructions
Using Nails or Push Pins
Measure the length of your bunting. Take a tape measure and measure the entire length of your bunting to determine the size of the space you'll need. Allow some slack in the bunting if you want it to hang loosely rather than being pulled tight all the way.
- If you're using flag bunting, pull it tight unless you want it to droop in the middle.
- If your bunting is strung on twine or cord, it should have a slight sag in the middle.
Mark where you want to hang your bunting. Use a tape measure to mark the spot where you want to hang your bunting. Make marks on both sides of the tape with a pencil.
- You can hang your bunting on a wall, a railing, or a windowsill if you're placing it outside.
- For indoor decorations, you can also hang small bunting on shelves, tables, or walls for a festive touch.
Secure a push pin or nail at each end of the marked area. For heavier bunting, hammer a nail into each mark. For lighter bunting or temporary hanging, use large push pins instead.
- If you're hanging bunting on a stone wall, carefully insert nails into the gaps between the stones.
Tie the ends of the bunting cord to the push pins or nails. Use the excess cord to tie each end securely to the pins or nails. Make sure to knot them tightly to prevent the bunting from coming loose.
- If your bunting has grommets, simply slide them over the nails or push pins.
Remove the nails using the back of a hammer to take down the bunting. When it's time to take down your bunting, remove the push pins and untie the cords. Alternatively, gently pry the nails out of the wall, windowsill, or shelves using the back of a hammer.
Tip: Store your nails or push pins in a plastic bag or container for future use when hanging up your bunting again.
Hanging with Adhesive Hooks
Determine the length of your bunting. Ensure your bunting is stretched out as you measure it, unless you prefer it to droop in the middle. You can note down the length or mark it directly on your wall.
Clean the hanging area with soap and water. Dampen a cloth with warm, soapy water and use it to clean the entire area where you intend to hang your bunting. Then, wipe off the soapy residue with a clean, damp cloth. Allow the area to air-dry for approximately 30 minutes until it's no longer damp.
- Adhesive hooks adhere better to clean surfaces free of dirt and debris.
- For best results, use adhesive hooks on wood or drywall surfaces. If you're hanging bunting on a brick wall, opt for brick clips.
- You can hang your bunting on a railing, windowsill, or above your front door.
Mark the bunting's length on the designated area. Use your measurement to make 2 to 3 pencil marks at each end and the midpoint of your bunting area. The accuracy of your marks will affect how well your bunting hangs.
Attach 2 to 3 hooks at each end and the midpoint of your bunting area. Remove the backing from 2 or 3 adhesive hooks and affix them approximately 1 inch (2.5 cm) above each mark. Space out the hooks evenly, placing 2 at each end and 1 in the middle.
- If you're hanging bunting on a brick wall, use brick clips by fitting 1 clip around each brick.
- For bunting on a windowsill, attach hooks to the upper part.
- If your bunting is on a string and you want it to hang loosely, skip the hook in the middle.
Pro Tip: If you're hanging bunting outdoors, opt for outdoor adhesive hooks. These hooks are designed to withstand the elements and provide longer-lasting adhesion to various surfaces.
Secure your bunting to the hooks using metal wire. Cut 1-inch (2.5 cm) lengths of metal wire and loop the top ends around the adhesive hooks. Wrap the bottom end of the wire around the bunting cord 2 to 3 times. If your bunting has grommets, you can wrap the wire around those instead.
- You can purchase metal wire at most hardware stores.
- If metal wire isn't available, twine can be used as an alternative.
Materials Needed
Using Nails or Push Pins
- Hammer
- Pencil
- Tape measure
- Nails or push pins
Hanging with Adhesive Hooks
- Tape measure
- Pencil
- Cloth
- Dish soap
- Adhesive hooks
- Metal wire
Helpful Tips
- Experiment with different locations around your home to find the perfect spot for your bunting!
- Enlist a friend or family member to assist you if you need help putting up your bunting.
