Top 5 Most Beautiful Velvet Wire Flower Crafts

Materials:

• Yellow velvet wire
• Green velvet wire
• Brown velvet wire
• Wire stems
• Green floral tape
• Scissors
• Hot glue gun

Instructions:

• First, cut 6 pieces of yellow wire in half. Bend them to form 2 petals. Repeat the same with the remaining 12 pieces of wire.
• Use a piece of brown wire to create the center of the flower by wrapping it around and threading the other end through the middle.
• Bend the green wire in half and twist 2.5cm of it to form 3 petals, adjusting the shape so that they are even. Twist the excess ends together, then repeat the process with another green wire.
• Take a long piece of green wire and cut two short pieces. Bend the short pieces and use the long wire to twist them together, securing them tightly to form leaves. Adjust the wire to create a puffed effect.
• Use the hot glue gun to attach the yellow petals around the center, starting with 6 petals evenly spaced. For the second layer, glue another 6 petals in a staggered position. For the third layer, attach the wire stem to the base of the flower. Use floral tape to secure the stem.
• Attach two leaves to the stem wire, adjusting them to the desired position.
• Finally, shape the flower petals, curve the stem, and adjust the leaves to complete your sunflower.

Materials:

• Purple velvet wire
• Green velvet wire
• Wire stems
• Green floral tape
• Scissors
• Hot glue gun

Instructions:

• Cut approximately 40 pieces of purple velvet wire, each about 6cm long, and bend both ends to secure them in place.
• For the leaves, take two green velvet wires, fold them in half, and secure the middle. Bend the ends gently to shape the leaves.
• Use floral tape to attach each flower petal to the wire stem, making sure each subsequent petal is positioned slightly lower than the one before.
• The first leaf is attached to the stem about 5cm from the flower base, and the second leaf is placed around 2cm below the first one.
• Add an additional wire stem by wrapping floral tape around it to extend the length of the flower's stem.
• Adjust the flowers and gently bend the petals to create a natural curve, completing your lavender flower arrangement.

Materials:

• Red velvet wire
• Artificial flower center
• Brown floral tape
• Scissors
• Flower vase
• Hot glue gun

Instructions:

• Cut the red velvet wire into 4cm pieces. Bend one end of each wire as shown in the image, then thread the other end through the circle and pull it tight to secure the petal. Repeat until you have the desired number of petals.
• Place the flower center on the top 2/3 of the wire, fold it over, and secure the shorter wire around the center to fix it in place. Attach the petals around the flower center using the floral tape to complete the peach blossom.
• For the bud, take a piece of velvet wire, bend one end, and wrap the brown tape around the wire, leaving the bent end exposed to form the flower bud.
• Wrap the floral tape around the remaining wire to form the flower stem. Carefully attach the flower center and petals to the stem, creating a natural-looking flower branch. This step requires skill and creativity to achieve the most realistic flowers.

Materials:

• Pink velvet wire
• Green velvet wire
• Wire stems
• Green floral tape
• Scissors
• Hot glue gun

Instructions:

• Prepare 6 pieces of velvet wire, bending each one to create a 5cm loop. Secure the ends and continue looping, threading the remaining wire through the middle. Repeat the same for all 6 petals.
• For the leaves, take two pieces of green velvet wire, twist them together and fold them to create the leaf shape. Secure the bottom with a piece of wire and bend the leaves slightly.
• Take a wire stem and attach the flower petals with tape. Start by adding 3 petals, then overlap 3 more petals in the second layer. Wrap the tape around 10cm of the stem and attach the leaves to complete the tulip arrangement.

Materials:

• Pink velvet wire
• Green velvet wire
• Light yellow velvet wire
• Wire stem
• Green floral tape
• Scissors
• Hot glue gun

Instructions:

• Take 9 pink velvet wires and cut them in half. Fold 3 short wires in half, then use a long piece to hook through the 3 short wires, twist to secure the joint. Use a long wire to tightly twist the ends. Bend the wire to create the petal shape and adjust for the desired puffiness. Fold the bottom of each petal to form a 90-degree angle.
• To make the leaves, take 3 green wires, fold them in half, and twist them together. Use another wire to bind them securely.
• Use the hot glue gun to attach 6 petals to the wire stem. Start by gluing 3 petals opposite each other, then glue the remaining 3 petals in between the first set. Add a small flower center using glue.
• For the flower center, use yellow wire, fold it in a zigzag pattern to form 5 points. Leave about 4cm at the end and bend it down to form a small stem. Glue the center firmly in the middle of the flower.
• Wrap the green wire around the flower stem and secure with hot glue. Use floral tape to cover the rest of the stem.
• Attach the first leaf 6cm from the base of the stem, and the second leaf 4cm from the first leaf.